COMPANY NAME:         Dial Manufacturing, Inc.

                                    25 S. 51st Avenue

                                    Phoenix, Arizona  85043

                                    Tel. No.: (602) 278-1100

HMIS

HEALTH:                          1

FLAMMABILITY:               2

REACTIVITY:                    0

PERS. PROT. EQUIP.:     A

PRODUCT NAME:         ALUMINUM CHROME COATING/X-COAT

PRODUCT CLASS: Aluminum Asphalt Cutback

PRODUCT NUMBER:           Dial     5378 - Quart

                                           Dial     5380 - Gallon

Ingredient/CAS Numbers

Petroleum Distillate     CAS #124185

Petroleum Distillate     CAS #64742-95-8

Percent

25 - 30%

3 - 7%

Occupational Exposure Limits

      TLV                  PEL

   500 PPM              500 PPM

                              100 PPM

Vapor

Pressure

5MM @ 72° F

3MM W 68° F

Boiling Range:               300-400 Deg. F.

Vapor Density:               Heavier than air

Evaporation Rate:           Slower than ether

Weight per Gallon:         Approx. 9.5 Lbs.

% Volatile Volume:          30 - 40%

% Water Volume:            0%

Maximum V.O.C.:           400 grams/liter

Flammability Classification :  OSHA:  II

DOT:  Combustible

Flash Point:       110 Deg. F

LEL:                 1%

Extinguishing Media:                              Foam, CO², Dry Chemical.

Unusual Fire and Explosion Hazards:      Water will spread fire.

Special Fire Fighting Procedures:            None

Effects of Over Exposure:

Headache, nausea, giddiness and loss of consciousness.  Nose, throat and eye irritation.  Extreme exposure may cause death by paralysis of respiratory center.

Medical Conditions Prone to Aggravation by Exposure:

Current anemia, respiratory or liver ailments.

Primary Route(s) of Entry:

Inhalation.

Emergency and First Aid Procedures:

Move person to fresh air.  Apply artificial respiration if needed.  Remove contaminated clothing.  Wash eyes with water 15 minutes.  If swallowed, DO NOT INDUCE VOMITING.  CALL PHYSICIAN!!

Comments:

The IARC Monographs (Vol. 35) reporting on mice painting studies states that there is sufficient evidence for the carcinogenity in experimental animals of extracts of some asphalts.  The same document states that there is inadequate evidence that asphalts alone are carcinogenic to humans.

Stability:

Stable

Hazardous Polymerization:

Will not occur

Hazardous Decomposition Products:

Smoke

Conditions to Avoid:

Heat and source of ignition

Incompatibility (Materials to Avoid):

Strong oxidizing agents

Steps to be taken in case material is released or spilled:

Extinguish all sources of ignition in the area.  Absorb spilled material with clay, diatomaceous earth or other non-flammable absorbent material.  Let dry in safe place.

Waste Disposal Method:

Dispose as solid waste in accordance with local regulations.

Respiratory Protection:

If TLV is exceeded, use organic respirator or supplied air system, avoiding sources of ignition.  Spray application releases particulate matter into the air.  To prevent inhalation of same, use proper respirator device as recommended by equipment manufacturer.

Ventilation:

Sufficient to keep vapors below TLV.

Protective Gloves:

Neoprene gloves to avoid repeated contact.

Eye Protection:

Safety goggles to protect from splashes.

Other Protective Equipment:

None

Hygienic Practices:

Wash skin with soap and water or waterless cleaner.  Do not use solvents.

Precautions To Be Taken In Handling and Storing:

Store away from sources of ignition.

Other Precautions:

None

D.O.T.:

Regulated

Shipping Name:

Cement, Roofing Liquid

Hazard Class:

Combustible Liquid

Label Required:

None

I.M.C.O.:     UN(NA)             No.:   1999           Class:   3.3           Page:   3126